Technology

How to connect two Routers Properly

How to connect two Routers

By connecting your routers, you’ll extend both the range and the maximum number of connections your Internet can handle. The simplest thanks to connecting two routers are using Ethernet, though you’ll be ready to use a wireless router to attach to the first router.

Methods 1 of 2:Using Ethernet

1. Determine which router is going to be the most. This may be the router that’s connected either to a fanatical modem or to the wall outlet

  • If you’ve got two of an equivalent router, it doesn’t matter which one you choose.

2. Determine which router is going to be the secondary router. This may be the router that’s extending your original network. You usually want to use your older router

  • This router will control the secondary network if you’re creating a LAN-to-WAN network

3. Place both routers near your computer. During the initial setup process, you ought to keep the routers near your computer so that you’ll easily access them. You’ll set them up in their permanent locations later.

4. Decide between a LAN-to-LAN or LAN-to-WAN connection. While you’ll use a coaxial cable for every one of these associations, they have slightly different uses.

  • LAN-to-LAN – Extends your Wi-Fi vary to include the second router. You will be ready to additionally use a LAN-to-LAN connection to share files between network-connected pcs, smartphones, so on.
  • LAN-to-WAN – Create a second network inside the foremost network, permitting you to place restrictions on any computers, smartphones, or various things connected to it. LAN-to-WAN networks cannot be used to share files.

5. Perform the initial router setup. Connect your main router to your equipment via a local area network cable, then connect your computer to the router via a special local area network cable.

  • If you’re employing a Mac, you presumably do not have an Ethernet port on your computer. you’ll buy an Ethernet to USB-C (also referred to as “Thunderbolt 3”) adapter to repair this problem.
  • On Windows computers that do not have Ethernet ports, you’ll buy an Ethernet to USB adapter.

6. Configure your router. Since this router will be handling the connection to the web, set it up as if you were only employing a single router.

  • you’ll access most routers by entering the router’s IP address during a browser.
  • Each router’s settings will vary substantially from other models. If you cannot find a particular setting or section on your router’s page for the remainder of this method, consult the router’s manual or online documentation.

7. Change the DHCP settings. If you’re creating a LAN-to-WAN network, attend the router’s page and set the first router’s DHCP service to offer out addresses between 192.168.1.2 and 192.168.1.50.

  • If you’re creating a LAN-to-LAN network, you’ll leave the DHCP settings at their default.
  • Disconnect the pc from the router once you are finished configuring it.

8. Configure the second router. Disconnect the primary router from your computer if necessary, connect the second router to your computer, and do the following:

  • Open the router’s page.
  • Change the IP address so that it matches the primary router and then increases the second-to-last digit by one (e.g., 192.168.1.1 becomes 192.168.1.128 and secures your router).
  • If you’re making a LAN-to-WAN network, change the secondary router’s WAN IP address to 192.168.1.51.
  • make sure that the “Subnet mask” number matches the one for your primary router.
  • Disable UPnP on the second router if it’s an option.

9. Configure the DHCP server on the secondary router.[2] If you’re creating a LAN-to-LAN network, the DHCP service should be turned off on the secondary router. If you’re creating a LAN-to-WAN network, the DHCP server on the secondary router needs to distribute addresses between one92.168.2.2 and 192.168.2.50.[3]

10. Change the wireless channel. If each router is wireless, you’ll wish to manually set the channels so that signals don’t interfere with every other. You will be ready to do this by setting your primary router to any channels from 1 to 6 and setting your secondary router to channel.

11. Place your routers. Currently, that everything is configured, you’ll place your routers where you would like. Confine in mind that you simply will need to be compelled to run coax between the two routers.

  • you will be ready to run local area network cable through the wall if you would like to succeed in another room.
  • For convenience, you’ll likely want to put your primary router near your modem.

12. Connect the two routers. Plug one end of the coaxial cable into any LAN port of the first router, then plug the opposite end of the cable into the LAN port on the rear of the second router.

  • If you’re creating a LAN-to-WAN network, plug the opposite end into the WAN (or “Internet”) port on the secondary router.

2 of 2:Using Wireless

1. Determine if your equipment is compatible. While most wireless routers are often used as wireless access points (also referred to as range extenders), most retail routers can’t create their network inside the first router’s network. To make a separate wireless network within the first router’s network, your secondary router must have “bridge” mode capabilities.

  • Your router’s documentation will allow you to know if it’s bridge mode. You’ll also look your router’s model up online.

2. Place both routers near your computer. During the setup process, it’ll be easier if you’ve got quick access to both routers, also because of the modem. You’ll place the routers in their permanent locations once you are done configuring them.

3. Perform the initial router setup. Connect your main router to your modem via a coaxial cable, then connect your computer to the router via a special coaxial cable.

  • If you’re employing a Mac, you presumably do not have an Ethernet port on your computer. You’ll buy an Ethernet to USB-C (also referred to as “Thunderbolt 3”) adapter to repair this problem.
  • On Windows computers that do not have Ethernet ports, you’ll buy an Ethernet to USB adapter.

4. Configure your router. Since this router will be handling the connection to the web, set it up as if you were only employing a single router.

  • you’ll access most routers by entering the router’s IP address during a browser.
  • Each router’s settings will vary substantially from other models. If you cannot find a particular setting or section on your router’s page for the remainder of this method, consult the router’s manual or online documentation.

5. Open the configuration page for the secondary router. Connect the secondary router to your computer with a coaxial cable and open the configuration page. You are not going to connect it to the modem. Find the “Internet” or “Wireless” setup page once you’ve got logged in.

6. Enable Bridge Mode. Select “Bridge ” from the “Network Mode,” “Wireless Mode,” or “Connection Type” menu on the Wireless page. If there’s no menu to pick these options, then your router likely doesn’t support bridging; however, you’ll still set it up with Ethernet.

7. Specify the secondary router’s IP address. Enter an IP address within the first router’s range. For instance, if the first router’s IP address is 192.168.1.1, enter 192.168.1.50 or something else inside the DHCP range of the first router.

  • make sure that the “Subnet mask” number for the second router is like the first router’s subnet mask.

8. Enter a singular name for your second router. This may assist you to know which router on the network you’re connecting to.

  • For instance, you would possibly have the first labeled “Den,” and therefore the secondary labeled “LivingRoom”.
  • make sure that the safety for both routers is WPA2, and confirm that they both use an equivalent password.

9. Place the secondary router. Once you’ve got the secondary router configured, you’ll place it where you would like it to repeat the signal. To take care of an honest connection, it should be placed during a location where it gets a minimum of fifty signal strength from the primary router.

  • Your second router can have the strongest signal once there is a direct line-of-sight between it and also the most router.